|EUROCAT 271 CLASSIC||EUROCAT 311 CLASSIC||EUROCAT 311 PLUS CLASSIC|
|Weight||785 kg||865 kg||925 kg|
|Working width||2,7 m||3,05 m||3,05 m|
|Transport width||2,65 m||3 m||3 m|
|PTO Input Speed||1000 rpm||1000 rpm||1000 rpm|
|Mower drums||4 pcs.||4 pcs.||4 pcs.|
|Mower blades||12 pcs.||12 pcs.||12 pcs.|
|Cutting height adjustment system||Spacer washers||Spacer washers||Central cutting height adjustment|
|Cutting height without spacer rings||40 mm||40 mm||-|
|Cutting height adjustment with 2 spacer rings||52 mm||52 mm||-|
|Power requirement||55 hp||60 hp||60 hp|
|Coverage||2,7 ha/h||3,2 ha/h||3,2 ha/h|
|Swath width without swath discs||-||-||-|
|Swath width with a pair of swath discs||1,4 m||1,4 m||1,4 m|
|Swath width with two pair of swath discs||0,9 m||1 m||1 m|
|Swath discs||One pair of swath forming discs||One pair of swath forming discs||One pair of swath forming discs|
|Mounting||CLASSIC headstock |
|Mounting option||A-frame |
|PTO shaft guarding||without freewheel |
|PTO shaft profile||1 3/8" 6-splines |
|Protection system||Roll-up front guard |
|Side guard can be folded |
|Standard equipment includes||Operator's manual |
Spare parts list
Blade changing tool
Telescopic top link, counter springs and chains
Infinitely variable PLUS cutting height adjustment
The hexagonal drive shaft is set down between the drums - this facilitates removing when needed.
The mower drums are screwed on the outside - therefore removing is easy.
Overlapping cover plates
The smooth running bevel gears run submerged in oil.
The robust cast bearing housing is precision-machined using CNC machining centres.
Central adjustment axle
Precision ball bearings for the toughest of applications.
Overlapping cover plates
Spacer rings for different cutting heights
Spacer rings are utilized for different cutting heights at mowers without central cutting height adjustment.
The saucers are supplied in two parts and screwed. Simple and inexpensive changing. High-cut saucers from fine-grained steel provide additional cutting height of + 20 mm. Cutting heights up to 85 mm are possible especially for arable forage.
Blade quick-change system
Press down the spring clamp by using a knife wrench. Remove the blade and slide the new blade into place. The blade holders are screwed with the mowing plates and can be changed quick and easy. In case of natural wear the blade holders can be displaced.
PLUS - Continuously variable adjustment of the cutting height
The cutting height is adjusted centrally for all mower drums - from 40 mm to 65 mm. The adjustment axle is not rotating. As a result the drum glide discs do not rotate when the mower is lifted. The robust adjusting device is maintenance free. The central axle of each rotor unit is protected through overlapping cover plates within the adjustability range. The whole adjustability range is greased for life and protects the adjustability against corrosion. A rubber bellow avoids the penetration of dirt and humidity - thus always an easy task.
The inner reel bodies have a smaller diameter for improved access. Especially with large forage quantities the swath formation improves and the drum mover is even lighter to pull.
Minimum weight was the main priority when designing the CLASSIC generation of front mowers. The compact construction of the sleek headstock and the implementation of lightweight pressed components are the key features of these mowers. The demand for effective suspension to optimise ground tracking has also been met in full by our EUROCAT CLASSIC.
Two powerful springs ensure a uniform ground pressure over the whole width of the cutter bar. The chain length can be used to quickly optimise the pressure of the cutter bar.
The headstock is the trademark of perfect ground tracking. The sophisticated linkage geometry brings the centre of gravity as close to the tractor as possible in all working positions. Gimbals on the cutter bar guide arms guarantee smooth freedom of movement. With a travel of +/- 8 degrees, the mower is guided accurately over each bump in the ground. Stabiliser springs inside the headstock keep the mower centred during transport.
The individually adjustable swathing discs place the forage in a swath of the desired width. Additional swathing discs are available for even narrower swath placement.
The side guards are strong full-length pressed steel parts. Hydraulic folding is available if required.
All drive elements are robust and large dimensioned. Two PTO shafts and a angle gear ensure reliable power transmission. Exceptional smooth running is guaranteed. A friction clutch and freewheel provide optimum protection. The gears run submerged in oil and are maintainance free