|FOX 300 D||FOX 350 D||FOX 400 D|
|Working width||3 m||3,5 m||4 m|
|Working depth||3 - 8 cm||3 - 8 cm||3 - 8 cm|
|Under frame clearance||475 mm||475 mm||475 mm|
|Gang spacing||510 mm||510 mm||510 mm|
|Number of discs||22 pcs.||26 pcs.||30 pcs.|
|Disc spacing||13 cm||13 cm||13 cm|
|Power requirement||75 HP||90 HP||100 HP|
|Mounting||Rear three-point |
|Mounting type||3 point linkage with cross shaft |
|Mounting category||Cat. II / 2 |
Cat. III / 3
|Disc hubs||Twin race ball bearings with six lip labyrinth seal |
Our newly developed FOX and FOX D compact combinations deliver smooth-running, fuel-saving seedbed preparation. Combined with a PÖTTINGER seed drill, this implement becomes a cost-effective seed drill combination.
Your benefits at a glance
Low drag resistance, fuel-saving seedbed preparation
High working speed
Short and compact design for optimum centre of gravity
Mulch drill combination with PÖTTINGER seed drills
During the development of the PÖTTINGER compact combinations, great attention was paid to compact dimensions and low drag resistance. This lets you use smaller tractors to deliver fuel-saving and efficient seedbed preparation.
The lugs for the lower linkages are mounted on bars that can be slid into three different positions. This enables the addition of frontal tools. In addition, two different top link positions make it easy to connect up and adapt to any tractor.
Combined with a PÖTTINGER seed drill, this implement becomes a cost-effective 3-point-mounted seed drill combination. The drill is mounted either on the packer roller or on the hitch.
With the FOX D the discs take over the preparation of the soil. These are mounted on rubber elements and are depth adjustable for use in slightly stony soils. The discs have a diameter of 410 mm and are fitted with sealed bearings.
PÖTTINGER offers a wide range of rear rollers for perfect results with the desired tilth in any type of soil. The whole range of rollers features precision manufacturing and robust design engineering.
The ideal roller for dealing with dry, non-sticky soils. The roller is fitted with strong rods for optimal compression.
Diameter: 420 mm, 8 bars
Diameter: 540 mm, 11 bars
This all-rounder is suitable for all types of soil. The roller leaves behind an optimum, re-packed seedbed with loose, fine soil at seed level. The scrapers are located just above surface level. That is why no earth clods can be lifted away, even in wet conditions, and a perfect capillary structure remains intact for optimum germination. The teeth are hardened right through. Coated scrapers also available.
Diameter: 420, 500 and 550 mm
The teeth are offset at an angle to the left and right. This roller is especially suitable for heavy, clay soils. The result is a deep packing effect with loose crumbling effect just under the surface. Coated scrapers (standard) prevent soil sticking to the roller.
Diameter: 525 mm
The packer rings are closed on either side and have a diameter of 550 mm with eight rings per metre of working width. The roller produces a corrugated consolidation effect to promote water absorption and allow the soil to breathe. Ideal for stony, damp conditions and heavy organic residues. Harvest residues remain on the surface of the soil and protect the soil against drying. Coated scrapers (standard) prevent soil sticking to the roller.
The Prism rings are spaced at 12.5 mm or 5.9 inch. This roller handles all operating conditions, including stony ground and larger quantities of harvest trash. The striped formation of re-consolidation promotes water absorption and breathability of the soil that is subject to less compaction in the gap between the rings. Coated scrapers are standard and help prevent soil sticking to the roller.
This roller is ideal for widely varied ground conditions. Especially for use with trailed implements where the load-bearing capacity of other rollers is near the limit. A diameter of 585 mm and the special profiling allows the soil to be compacted in rows. Coated scrapers (standard) prevent soil sticking to the roller.